Honey extractor drive electric, horizontal voltage 12 V Euro (aluminum housing, Kharkiv region.

Electric drivehoney chaser electric worm with aluminum housing.

It is needed to speed up and facilitate the pumping of honey. The electric drive works from a battery with a voltage of 12 V, and is also powered from a 220 V network through a power supply unit. The rotor revolutions are regulated by the control unit.

This electric drive uses a reducer with a worm gear. A big advantage of this design is the use of electronic engine with low required power, due to which there is minimal energy consumption at nominal revolutions. Also, due to the gearbox, torque is created, which is necessary for the rotation of the rotor without overloading the bearings and overheating the engine from belt tension.

The use of a closed type electric motor excludes the ingress of various particles.

75 W electric motor.

Regulation of revolutions from 60 to 180 rpm.

The weight of the drive is 2.5 kg. (without control unit)

Weight with control unit 舒 3,250 kg

Frames with honey do not affect the speed of the rotor.

Gear shaft diameter: 14 mm

Gear shaft length: 50 mm.

The control unit has 9 automatic and manual modes.

Characteristics of automatic mode

Program 1: -direction of rotation, forward: 50 rpm, working time 1.5 min.

-direction of rotation, back: 65 rpm, working time 1.5 min.

-direction of rotation, forward 65 rpm, working time 1.5 min.

Program 2: -direction of rotation, forward: 50 rpm, working time 1.5 min.

-direction of rotation, backward: 75 rpm, working time 1.5 min.

-direction of rotation, forward 75 rpm, working time 1.5 min.

Program 3: -direction of rotation, forward: 50 rpm, working time 1.5 min.

— direction of rotation, backward: 85 rpm, working time 1.5 min.

-direction of rotation, forward: 85 rpm, working time 1.5 min.

Program 4: - direction of rotation, forward: 50 rpm, working time 1.5 min.(//tractor-service.com)

-direction of rotation, back: 95 rpm, working time 1.5 min.

-direction of rotation, forward 95 rpm, working time 1.5 min.

Program 5: -direction of rotation, forward: 50 rpm, working time 1 min.

-direction of rotation, back: 55 rpm, working time 1.5 min.

-direction of rotation, forward: 75 rpm, working time 1.5 min.

- direction of rotation, backward: 75 rpm, working time 1.5 min.

Program 6: -direction of rotation, forward: 50 rpm, working time 1 min.

-direction of rotation, backward: 55 rpm, working time 1.5 min.

-direction of rotation, forward: 85 rpm, working time 1.5 min.

- direction of rotation, back: 85 rpm, working time 1.5 min.

Program 7: -direction of rotation, forward: 50 rpm, working time 1 min.

-direction of rotation, backward: 55 rpm, working time 1.5 min.

-direction of rotation, forward: 95 rpm, working time 1.5 min.

- direction of rotation, backward: 95 rpm, working time 1.5 min.

Program 8 - direction of rotation, forward: 50 rpm, working time 1 min.

-direction of rotation, back: 55 rpm, working time 1 min.

-direction of rotation, forward: 80 rpm, working time 2 min.

-direction of rotation, backward: 80 rpm, working time 2 min.

Program 9 - direction of rotation, forward: 50 rpm, working time 1 min.

-direction of rotation, back: 55 rpm, working time 1 min.

-direction of rotation, forward: 90 rpm, working time 2 min.

- direction of rotation, backward: 90 rpm, working time 2 min.
Specified in the tables RPM ±5% at 220V mains voltage.